engine oil AUDI A4 1999 B5 / 1.G APB Engine Lubrication System Components Workshop Manual

17-1


Lubrication system
components, removing and
installing

Notes:

If large quantities of metal particles or other
deposits (caused, for example, by partial
seizure of the crankshaft or connecting rod
bearings) are found in the engine oil when
performing repairs, clean the oil passages
thoroughly and replace the oil cooler in order to
prevent further damage from occurring later.
Always replace O-rings, gaskets and oil seals
when performing repairs.
The oil level must not be above the max. mark -
otherwise this can cause damage to the
catalytic converter. Markings Page 17
-67

Viscosity grades and oil specifications
Repair Manual, Maintenance

Oil capacities
Repair Manual, Maintenance

Checking oil pressure Page 17
-65

Pa
ge 1 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-8


Oil pump, oil pan, oil filter and oil cooler,
removing and installing

1 -
Bolt for dipstick guide tube
Tightening torque: 25 Nm
2 -
Dipstick guide tube Replace O-ring
3 -
Oil pan - upper section There is no gasket between engine block
and upper section of pan. Only use silicone
sealant D 454 300 A2.
4 -
Hex socket head bolt M8 Tightening torque: 20 Nm
5 -
Hex bolt M6 Tightening torque: 15 Nm
Pa
ge 8 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-10


12 -
Hex bolt M6
Tightening torque: 10 Nm
13 -
Oil pan - lower section
14 -
Hex bolt M6 Tightening torque: 10 Nm
15 -
Retainer for oil lines
16 -
Oil supply line From pump to oil filter
17 -
Oil supply line From oil filter to engine oil system
18 -
O-ring Always replace
Pa
ge 10 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-11


19 -
O-ring
Always replace
20 -
Oil filter
21 -
Hex nut Tightening torque: 30 NmThreaded line for oil cooler and oil filter is
screwed into upper section of pan with 20
Nm tightening torque.
22 -
Oil cooler Ensure O-ring is installed correctly when
installing
23 -
Oil pump Driven off crankshaft via chainTightening torque of chain sprocket to oil
pump: 25 Nm Tightening torque of oil pump to engine
block: 25 Nm
Pa
ge 11 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-12

Oil check valves, replacing


Note:
If irregular valve noise occurs repeatedly during
short journeys and disappears after extended
driving, the oil check valves must be replaced.

All cable ties which are released or cut open
when removing the engine must be replaced in
the same position when installing the engine.
Catch drained-off coolant in a clean container
for re-use or disposal.
Replace all gaskets and seals.

Removing

- Remove bolts -arrows- and remove engine cover panels -A...C-.
- Remove cover above air cleaner.
Pa
ge 12 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-27

WARNING!

Do not open air conditioner refrigerant
circuit.

Notes:
Note:
Use a separate container to collect the engine oil. - Detach air conditioner compressor -1...2-.
Watch position of guide bushes when installing.When installing, insert bolt -1- in the compressor first. To prevent damage to the condenser and refrigerant lines/hoses,
ensure that the lines and hoses are not stretched, kinked or bent.
- Drain engine oil.

- Remove lower section of oil pan.
Pa
ge 28 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-29

- Fill engine with oil.

Repair Manual, Maintenance


- Install lock carrier in normal position.

Repair Manual, Body Exterior, Repair Group
50


- Install bumper.

Repair Manual, Body Exterior, Repair Group
63

Pa
ge 30 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-31

Installing
Install in the opposite order to removing. When
installing, note the following points:

- Fill up engine oil.

Repair Manual, Maintenance


- Install lock carrier in normal position.

Repair Manual, Body Exterior, Repair Group
50


- Install bumper.

Repair Manual, Body Exterior, Repair Group
63

Pa
ge 33 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-32

Upper and lower sections of oil pan,
removing and installing


Special tools, testers and equipment
required

Engine support bracket 10-222A with adapter
10-222A/3
Drip tray VAG 1306
Electric drill with plastic brush attachment
Silicone sealant D 176 404 A2
Torque wrench 10 Nm/ 45 Nm

- Obtain radio theft code on vehicles with coded
radio.

- With ignition switched off, disconnect battery
Ground strap.

- Pull out dipstick.
Pa
ge 34 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-33

- Unbolt dipstick guide tube at front of cylinder
head (right side), and pull out of oil pan from the
top.

Repair Manual, Body Exterior, Repair Group 63

Repair Manual, Body Exterior, Repair Group 50
WARNING!
Hot steam can escape from the expansion tank when the filler cap is
opened. Cover the filler cap with a cloth and remove it carefully. - Remove noise insulation panel -arrows-.
- Remove bumper.
- Move lock carrier to service position.- Remove cap on coolant expansion tank.
- Place drip tray VAG 1306 below engine.

- Turn drain screw -arrow- on radiator anti-clockwise, if necessary install
drain hose to connection.
Pa
ge 35 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1